If you’re looking for a quick and easy way to hotwire a moped, all you need is a screwdriver. With this simple tool, you can bypass the ignition and get your moped up and running in no time.
How To Hotwire A Moped With A Screwdriver? First, you’ll need to find the right screwdriver for the job. A flathead screwdriver will work best. Next, locate the moped’s ignition system. This is usually located near the moped’s engine. Once you’ve found the ignition system, insert the screwdriver into the ignition and turn it clockwise.
A moped is a great way to get around town if you don’t have a driver’s license or don’t feel comfortable driving a car. When you’re ready to go beyond the city limits, though, you’ll need to know how to hotwire a moped.
This is easy with a screwdriver. Just be sure that your moped has the appropriate electrical system before beginning, and be aware of the safety precautions that must be followed while doing this.
Can You Start A Motorcycle With A Screwdriver?
If you’re looking to start your motorcycle using a screwdriver, there are a few things you’ll need to keep in mind. First and foremost, make sure the bike is properly secured. If the bike isn’t properly fastened down, it could easily fall over while you’re working on the engine.
Secondly, be very careful when turning the screws, they can easily strip if not handled correctly. And finally, always wear safety equipment such as gloves and eye protection when working with engines even if you have experience doing so.
How Easy Is It To Hotwire A Motorcycle?
A motorbike, more often than not, is a mechanically simple machine. All you need is a turning key, an ignition switch and the willingness to twist things around.
The most difficult part of hotwiring a motorcycle might be locating the sparkplug wire, it’s not always at the same spot on every bike.
How Do You Start A Motorcycle With A Screwdriver?
First, make sure the battery is disconnected. Next, remove the ignition cover by unscrewing the two screws on either side of it. Finally, disconnect the wires from the spark plugs by gently pulling them out of their sockets.
Once those steps are complete, it’s time to get to work. Find the wire that connects your battery to your starter motor and use a Phillips head screwdriver to unscrew it. Be careful not to pull on the wires too much as they can easily be pulled out of their terminals.
Once that wire is unscrewed, you can start connecting your new wire in its place. Repeat these steps for each spark plug until all four are connected and re-inserted into their sockets.
Finally, replace the ignition cover and enjoy your new motorcycle.
More: How To Bypass Ignition Switch On Electric Scooter?
Things Needed To Hotwire A Moped With Screwdriver:
In order to hotwire a moped with a screwdriver, you’ll need some items:
- A Screwdriver
- A Claw Hammer
- A Flat Heated Screwdriver
- A screwdriver
- Wire cutters or a knife
- The key to the bike
- Four spark plugs
- An ignition cover
- Wire cutters
- A battery
- A starter motor
Get A Screwdriver:
The first step is to get a screwdriver. A standard size screwdriver will work just fine. Remove the handle of the moped by unscrewing it from the stem. You’ll see two Phillips head screws holding it in place. Remove them and set them aside.
Slip The Screwdriver Inside The Ignition Barrel:
Slip the screwdriver inside the ignition barrel. This is usually located on the left side of the bike near the handlebars. Once you have access to the screwdriver, turn it until it starts making clicking noises.
This means that it has successfully reached the spark plug. Now all you need to do is replace the spark plug with one that has been pre-wired for hotwiring and start your engine.
Locate The Battery:
The next step is to locate the battery. This can be done by looking for an access panel near the handlebars or searching under the seat.
Assuming you accessed the battery, next locate the wires that lead to it. There are typically two white wires and a red wire. The white wires go to the positive terminal and the red wire goes to the negative terminal.
If your moped has a keyless start, locate the keypad near the handlebars and press down on it until you hear a clicking sound. This will turn on the engine.
More: How To Hotwire A Lime Scooter?
Remove The Seat And The Battery Cover:
Once you have located the battery, it’s time to remove the cover. Use your screwdriver to pry it off gently and then discard it.
The moped has a few wires that you will want to disconnect before proceeding. The first is the battery lead, which you can do by removing the screw that connects it to the battery. This screw is located on the left side of the bike near the front wheel.
Once this screw is removed, gently pull away on the lead until it comes out of the connector. You’ll now need to remove another two screws from near where the battery was located.
Once these screws are removed, you can gently pull up on both sides of the battery cover and it will come off. Make sure to discard this cover as it will not be needed.
Loosen The Tensioner:
When you are trying to hotwire a moped, the thing you need to do is loosen the tensioner. This is done by turning it counter-clockwise with a screwdriver.
Once it has been loosened, you can then use your hands to unscrew the bolt that holds the tensioner in place. Once it has been unscrewed, you can then remove it.
More: How To Start A Scooter?
Disconnect Cables And Wires:
Next, disconnect any cables and wires that are attached to the battery. Make sure not to lose any of these connections.
Next, locate the screw that holds down the battery cover. Use a Phillips head screwdriver to unscrew this screw.
Once this screw is removed, lift up the battery cover and remove the battery. Finally, replace the battery and reattach any cables and wires you disconnected earlier.
Insert A Screwdriver Into The Wires:
The screwdriver needs to have a blade on one end and a Phillips head on the other. Insert the Phillips head into the wires near the battery, turn it until the battery light comes on, then remove it.
Do this to all the wires near the battery. Next, insert the blade end of the screwdriver into one of the connectors near where you changed out the battery.
Turn it until you hear a click, then remove it. Repeat this process for each connector. Finally, connect all of the connectors with wire using crimps or clips as needed.
More: 49cc Carburetor Hoses Diagram:
Connect Cables And Wires:
Now that all of the connections are made, it’s time to reconnect them in reverse order! Start by connecting one wire to another wire, then connect that wire to the cable that was disconnected previously. Do this until all of the wires are connected again.
Once all of the wires are connected in reverse order, it’s time to test your work. Start the engine and check to see if the moped is working properly.
Activate The Ignition Switch:
There are a few ways to start a moped if you don’t have the key. One is to turn the ignition switch to “on” but leave it in the “stand” position. Another is to hold down both the brake and accelerator pedals at the same time until you hear the moped start.
If you’re having trouble with your key, there’s another way to hotwire a moped. This involves using a screwdriver to activate the ignition switch. Make sure that you have all of your tools ready before starting, including a screwdriver, wire cutters, and an extra set of keys.
Watch Video: How To Hotwire A Moped With A Screwdriver
Replace Battery Cover:
Once everything is connected, replace the battery cover and re-attach any screws that may have been loosened during Steps 3-5.
Replacing the battery cover and re-attaching any screws can be a tedious task, but it is important to make sure that the moped is securely attached before proceeding. Once everything is connected, replace the battery and test the system to ensure that it works properly.
Test Ride:
Finally, test ride your moped and make sure everything is working as it should. If everything is good, you’re ready to start hotwiring it.
Final Words: How To Hotwire A Moped With A Screwdriver?
Congratulations on your new moped! Now that it’s complete, you’ll need to install the essential components: the battery, the handlebar grip, and the motor and gearbox covers.
Hotwiring a moped with a screwdriver is a simple and effective way to start your moped without keys. This method is also relatively safe, as long as you take precautions not to shock yourself. With a little practice, anyone can hotwire a moped in minutes.
FAQs
I’m having trouble removing the Phillips head screws that secure the motor cover in place. What should I do?
Try prying it off with a flathead screwdriver. If that doesn’t work, use a pointed object to pry it off from the inside.
How Do You Break An Ignition With A Screwdriver?
If you’re looking to start your engine on a moped but don’t have an ignition key, there are a few methods you can use to get the job done. The easiest way is to remove the battery cap and use a screwdriver to pop the ignitor coil unit out.
Be careful not to damage the coil unit or wires while doing this. Once it’s out, Pry off the spark plug cover and use a flathead screwdriver to unscrew the spark plug. Finally, remove the wire from the spark plug lead and reattach it to the ignitor coil unit.
