Where Is Gotrax Scooter Reset Button Located?

Gotrax Scooter Reset Button: The Gotrax scooter reset button is a device used to re-initialize the electrical system of the scooter.

It serves as an effective tool for restoring the normal functioning of this type of transport mechanism, allowing it to perform at peak efficiency levels.

The reset button is typically engaged when the scooter’s electrical system has experienced a power interruption or been exposed to sudden changes in voltage or frequency.

If you are having trouble finding the reset button on your Gotrax scooter, then this article is for you. This guide will provide step-by-step instructions to help you locate the reset button on your Gotrax scooter.

We’ll go over where to find the reset button, how to use it, and some additional tips to help you get the most out of your Gotrax scooter.

Where Is Gotrax Scooter Reset Button Located?

Gotrax Scooter Reset Button: The reset button on a Gotrax scooter is located on the stem of the handlebar. To access, simply remove the two screws securing the plastic cover and then you will find the reset button inside.

It is a small round button, similar to a computer mouse. Pressing it will reset the device. Once complete, replace the plastic cover back and secure with the screws.

How To Find Your Gotrax Scooter Reset Button?

To find the reset button, start by locating the power key. This is usually a circular button that lights up when you press it. From there, look for three buttons located on the lower right-hand side of the power key.

These are the reset, power off, and power on buttons. The reset button will be the topmost of the three buttons and is usually marked with a red circle.

How To Use Your Gotrax Scooter Reset Button?

The reset button can help you troubleshoot any problems and get back on the road in no time. Here’s how to use it. First, locate the reset button on the scooter, which is usually located near the power switch.

Next, press and hold the reset button for around 10 seconds until you hear a beep. This will reset your scooter’s settings.

Finally, turn the power switch back on to see if the problem has been fixed.

How To Reset A Gotrax Scooter Using The Button?

If your scooter is not working, you may need to reset it using the button. So, how to factory reset gotrax scooter? This will reset your scooter’s settings and get it back in working condition. Here are the simple steps to reset your Gotrax scooter:

1: Remove The Stem Cap And Find The Gotrax Scooter Reset Button:

To reset your Gotrax scooter, first locate the stem cap on the handlebar shaft. Once you’ve found it, remove the stem cap with a flathead screwdriver.

After removing the stem cap, you’ll find the Gotrax scooter reset button directly underneath.

Press and hold the reset button for approximately 10 seconds until you hear a beep indicating that your scooter has been reset.

2: Press And Hold Power Button For 5 Seconds:

Pressing and holding the power button is a quick and easy way to turn on and off most Scooters. It is also a great way to reset your scooter if it is not responding.

If your scooter is completely unresponsive, pressing and holding the power button for several seconds can help you reset it without losing any of your data.

If you are still having trouble, try pressing and holding the power button for even longer, up to 10 seconds. Doing this may help you reset your scooter without any further issues.

3: You Can Release Power Key When Gotrax Scooter Display Is Blacked Out:

All you have to do is press the power key. This will reset the display and restore it to its normal functioning state.

It’s important to note that you should only press the power key when the display is blacked out, pressing the key when the display is still working could cause further damage.

If you’re having trouble locating the power key, it’s typically located on the side of the scooter near the handlebar stem.

Once you’ve pressed the power key, you should expect to see the Gotrax scooter display light up again.

4: Power On Gotrax Scooter By Pressing Power Button Again:

Now all you need to do is press the power button again. Doing so will power your Gotrax scooter back on and you will be ready to ride once more.

It is important to note that if your Gotrax scooter does not power on after pressing the power button again, it may indicate a more complex issue with the scooter’s battery or motor.

5: Now Gotrax Should Restore Its Normal Operation:

Gotrax is back and stronger than ever! With these changes in place, Gotrax is now ready to serve you with an even higher level of efficiency and reliability.

6: Turn On The Power To Confirm Operation: 

If everything looks good, you can now turn on the power to confirm operation. Doing so will ensure that all systems are operational and that your scooter is ready to ride.

If you encounter any issues while powering up your Gotrax, be sure to contact a certified technician for assistance.

However, most users should be able to power up their scooters without any problems.

What Are Gotrax Scooter Error Codes?

Gotrax scooters are a great way to get around town, but they can sometimes display errors codes. If you’re seeing an error code on your Gotrax scooter, it can be helpful to know what the code means.

Error codes can provide an indication of what is wrong with the scooter and how you can fix it.

The most common Gotrax scooter error codes are E1, E2, E3, E4, and E5. Each code has a different meaning and indicates a different problem with the scooter.

Code E1 indicates a low battery voltage, which may mean that your battery needs to be charged or replaced.

Code E2 indicates communication failure between the mainboard and the controller, while Code E3 is related to the speed limit setting.

Code E4 is related to a throttle sensor issue, and Code E5 is related to an internal fault within the motor. Knowing what each of these codes means can help you assess the issue and take steps to fix it.

It’s important to note that you should always refer to the instruction manual for your specific Gotrax scooter model when troubleshooting any error code.

With the right information, you can identify and resolve most Gotrax scooter errors quickly and efficiently.

What Is The Default Code For Gotrax Scooter?

If you own a Gotrax scooter, you may be wondering what the default code is. The default code for your Gotrax scooter is 0000. This code is automatically set by the manufacturer, and it can be used to unlock and start your scooter.

Of course, it is important to note that you can change the code if you want to add an extra layer of security. Simply access the settings on the scooter and select “Change Password.”

However, if you ever forget your new code, you can always return it to the default code of 0000.

How to Reset Gotrax Scooter G2:

To reset your Gotrax G2 scooter, follow these steps:

1. Turn off your scooter. Make sure that the power button is turned off and that the lights are not illuminated.
2. Locate the reset button. The reset button is usually located on the underside of the deck, near the battery pack. It may be covered by a rubber flap.
3. Press and hold the reset button for 5-10 seconds. You may need to use a pen or other small object to press the button.
4. Release the reset button. The lights on your scooter should flash briefly, indicating that the reset was successful.
5. Turn on your scooter. Your scooter should now be reset and ready to use.

Gotrax G4 Hard Reset:

A hard reset on a Gotrax G4 electric scooter will erase all user data and settings and restore the scooter to its factory default state. This can be useful if you are troubleshooting a problem with your scooter or if you want to sell it to someone else.

To perform a hard reset, follow these steps:

1. Turn off your scooter and make sure it is plugged into a charger.
2. Hold down the power button and the minus button simultaneously for 10 seconds.
3. The lights on your scooter will flash and the scooter will beep.
4. Once the beeping stops, your scooter has been reset.

How to Unlock Gotrax Scooter?

nlocking a Gotrax scooter can be done in two ways: using the app or using the physical key.

Using the app:

1. Download and install the Gotrax app on your smartphone.
2. Create an account and sign in.
3. Select your scooter from the list of available devices.
4. Enter your password to unlock the scooter.

Using the physical key:

1. Locate the keyhole on the scooter. It is usually located on the underside of the deck, near the battery pack.
2. Insert the key into the keyhole and turn it to unlock the scooter.

Gotrax Scooter Password Reset:

The password reset process for a Gotrax scooter depends on the model of the scooter. Here are the steps on how to reset the password for two common Gotrax scooter models:

Gotrax G4

1. Turn on your scooter.
2. Press the plus button twice.
3. Enter your new four-digit password using the plus and minus buttons.
4. Press the power button twice to confirm your new password.

Gotrax G2

1. Turn off your scooter.
2. Press and hold the power button and the minus button for 10 seconds.
3. Enter your new four-digit password using the plus and minus buttons.
4. Press the power button twice to confirm your new password.

Watch Video: Gotrax Scooter Reset Button:

Conclusion: Gotrax Scooter Reset Button:

Gotrax Scooter Reset Button: If you’re experiencing issues with your Gotrax scooter, don’t hesitate to reach out for help.

The team at Gotrax is committed to providing the best possible customer service, and we’ll do everything we can to help you solve your problem.

Be sure to check out our website and learn about the different error codes that can be displayed on your scooter. Then, be sure to contact us for assistance.

We want to make sure that you have a positive experience when using your Gotrax scooter, and we’ll do everything we can to help make that happen.

FAQs